accessfleet
Registered User.
- Local time
- Yesterday, 23:40
- Joined
- Sep 29, 2010
- Messages
- 91
I am using access2007 to document vehicle maintennance repairs.
I have been thinking about the next revision.
In the Workorder “instructions & crew remarks” I have add a default value “check inspection expiration date, lights, tire pressures and fluid levels”
I would like to expand this a little.
From the Work Type drop down, when “PMA Maint” is selected I would like to append the “instructions and crew remarks” with additional text
1. Change oil and filter including mounted equipment.
2.Lubricate chassis, door locks/hinges and grease all fittings. Include all mounted equipment also.
3.Visually check brake lines/hoses, belts, steering linkage, shock absorbers, rear springs, exhaust system,
and universal joints.
4. Adjust brakes as needed.
5.Check all fluid levels on brake master cylinder, steering, differential, transmission and battery.
6.Check starter draw and alternator output and battery connections clean battery cable ends and post.
7.Check all lights and repair if necessary. Including trailer connection.
8.Check tire pressures, record tread depths. Inspect tire condition and rotate if needed.
9. Drain air tank if equipped with air brakes.
10. Check all hydraulic hoses, motors, gauges, controls & fluid levels. (Mounted Equipment)
11. Do an operational check & lube all bucket pins, hinges.
Or, From the Work Type drop down, when “PMC Maint” is selected I would like to append the “instructions and crew remarks” with additional text
1. Change oil and filter including mounted equipment.
2.Lubricate chassis, door locks/hinges and grease all fittings. Include all mounted equipment also.
3.Visually check brake lines/hoses, belts, steering linkage, shock absorbers, rear springs, exhaust system,
and universal joints.
4. Adjust brakes as needed.
5.Check all fluid levels on brake master cylinder, steering, differential, transmission and battery.
6.Check starter draw and alternator output and battery connections clean battery cable ends and post.
7.Check all lights and repair if necessary. Including trailer connection.
8.Check tire pressures, record tread depths. Inspect tire condition and rotate if needed.
9. Drain air tank if equipped with air brakes.
10. Check all hydraulic hoses, motors, gauges, controls & fluid levels. (Mounted Equipment)
11. Do an operational check & lube all bucket pins, hinges.
12. Replace air filter. Including brake air compressor unit.
13.Replace fuel filter and PCV valve. Drain fuel water separator if so equipped.
14.Engine tune-up. Replace spark plugs. Check ignition system.
15.Repack bearings, replace wheel seals and adjust bearing preload.
16. Pull wheels and inspect brakes replace if necessary.
17. Service automatic transmission, replace trans filter.
18.Change gear lube on manual transmission and differentials.
I have been thinking about the next revision.
In the Workorder “instructions & crew remarks” I have add a default value “check inspection expiration date, lights, tire pressures and fluid levels”
I would like to expand this a little.
From the Work Type drop down, when “PMA Maint” is selected I would like to append the “instructions and crew remarks” with additional text
1. Change oil and filter including mounted equipment.
2.Lubricate chassis, door locks/hinges and grease all fittings. Include all mounted equipment also.
3.Visually check brake lines/hoses, belts, steering linkage, shock absorbers, rear springs, exhaust system,
and universal joints.
4. Adjust brakes as needed.
5.Check all fluid levels on brake master cylinder, steering, differential, transmission and battery.
6.Check starter draw and alternator output and battery connections clean battery cable ends and post.
7.Check all lights and repair if necessary. Including trailer connection.
8.Check tire pressures, record tread depths. Inspect tire condition and rotate if needed.
9. Drain air tank if equipped with air brakes.
10. Check all hydraulic hoses, motors, gauges, controls & fluid levels. (Mounted Equipment)
11. Do an operational check & lube all bucket pins, hinges.
Or, From the Work Type drop down, when “PMC Maint” is selected I would like to append the “instructions and crew remarks” with additional text
1. Change oil and filter including mounted equipment.
2.Lubricate chassis, door locks/hinges and grease all fittings. Include all mounted equipment also.
3.Visually check brake lines/hoses, belts, steering linkage, shock absorbers, rear springs, exhaust system,
and universal joints.
4. Adjust brakes as needed.
5.Check all fluid levels on brake master cylinder, steering, differential, transmission and battery.
6.Check starter draw and alternator output and battery connections clean battery cable ends and post.
7.Check all lights and repair if necessary. Including trailer connection.
8.Check tire pressures, record tread depths. Inspect tire condition and rotate if needed.
9. Drain air tank if equipped with air brakes.
10. Check all hydraulic hoses, motors, gauges, controls & fluid levels. (Mounted Equipment)
11. Do an operational check & lube all bucket pins, hinges.
12. Replace air filter. Including brake air compressor unit.
13.Replace fuel filter and PCV valve. Drain fuel water separator if so equipped.
14.Engine tune-up. Replace spark plugs. Check ignition system.
15.Repack bearings, replace wheel seals and adjust bearing preload.
16. Pull wheels and inspect brakes replace if necessary.
17. Service automatic transmission, replace trans filter.
18.Change gear lube on manual transmission and differentials.